
Choosing between a square housing and an aluminum casing motorized screen is an installation and project-specification decision, not simply an appearance choice. The housing profile affects how the screen sits on the wall or ceiling, how the brackets are coordinated, how the cable route is hidden and how service access is maintained.
The screen surface, projector geometry and room conditions still control the image. Use this guide to compare the structure before requesting a model drawing.
Compare the Square Housing Electric with the Square Aluminum Casing Electric as separate product configurations. A square outline and an aluminum construction describe different properties; neither establishes strength, serviceability or optical performance on its own.
| Per-model drawing field | Installation decision |
|---|---|
| Cross-section, outer length and end-cap envelope | Check exposed appearance, corner obstruction and the complete ceiling envelope |
| Bracket centres, support interface and installed mass | Have the responsible installer verify the supporting structure and approved fixing arrangement |
| Cable-entry end and controller location | Align power/control pathways with that exact version; do not assume reversible ends |
| Service side / removal path | Exclude a proposal trapped by the wall corner, ceiling or fixed joinery |
| Surface and visible image | Approve optical pairing separately from casing finish or material |
Enter drawing number, revision, applicable size and reviewer against each proposal. Numerical dimensions, weight ranges and fixing locations remain unassigned until the model documents are supplied; this is a quote-comparison schedule, not a construction detail.
Send visible size, exposed/concealed location, ceiling section, power-entry preference, controls and finish requirements. Request the Two Housing Drawing Sets.
Choose a housing direction from four questions:
If a project has no special casing constraint, begin with the electric projection screen range and narrow the choice using image size, mounting method and material.
This guide is for AV integrators, distributors, contractors and project buyers who need a documented selection and project-planning path for this topic before requesting a quotation.
A square or rectangular housing can present a clear geometric line above the image. It may coordinate with architectural details, ceiling edges or a wall-mounted AV package. Its external shape can also make it easier for a project team to read the installation envelope on an elevation drawing.
The exact benefit depends on the current model. Confirm the outer dimensions, bracket locations, cable entry, image drop and clearance rather than assuming that every square casing shares the same construction.
An aluminum casing can be considered when the project wants a defined metal enclosure and a clean finish. Aluminum is a material description, not a guarantee of a particular size, weight or performance. The final product still depends on the roller, motor, fabric, bottom bar and mounting system.
For a compact casing direction, compare the 80mm aluminum housing guide and request the model drawing. For a round profile, see the 95mm round housing guide.
| Decision point | Square housing | Aluminum casing / profile | Confirmation required |
|---|---|---|---|
| Visual language | Geometric and architectural | Defined metal enclosure | Finish and visible casing detail |
| Mounting | Wall or ceiling, model dependent | Wall or ceiling, model dependent | Bracket and fixing drawing |
| Image quality | Not determined by shape | Not determined by shape | Material, geometry and flatness |
| Service access | Depends on access panel and position | Depends on access panel and position | Motor and control service route |
| Material choice | Model dependent | Model dependent | Current material compatibility |
| Concealed installation | Only with documented design | Only with documented design | Rough-in, closure and access |
Keep the full product name on the shortlist. Square describes a profile direction, aluminum describes a material direction, and standard identifies a catalogue entry. Collapsing them into “square electric screen” can send the buyer to a different product before the fit review has even begun.
| Catalogue reference | Identification value | Installation question it opens |
|---|---|---|
| Standard Electric | Separately listed ordinary electric candidate | Which selected-size housing and mounting arrangement fits? |
| Square Housing Electric | Square-housing product family | Does its actual silhouette and depth suit the intended elevation or joinery? |
| Square Aluminum Casing Electric | Distinct aluminum-casing entry | Which finish, section and mounting data belong to this entry? |
| Hexagonal Electric | Hexagonal-housing candidate | Does the complete product profile fit the available room section? |
| Premium Aluminum Casing Tab-tension Electric | A casing and side-tension combination | Do housing and additional deployed side components fit the image task and space? |
| Hexagonal Tab-Tension Electric | Separate hexagonal tab-tension entry | Which specific envelope, surface and mounting arrangement are proposed? |
The product-page views help participants recognise the candidate and compare visible appearance. They do not provide dimensional evidence for a different size or configuration. Keep any reference image connected to its exact catalogue source.
Standard Electric Projection Screen is not a generic base-name suffix for the Square Housing or Square Aluminum Casing entries. Square Housing Electric Projection Screen and Square Aluminum Casing Electric Projection Screen share a word, but do not thereby share supports, overall dimensions or accessories.
If an approved Square Housing submission later receives a quotation shortened to “square aluminum electric,” compare the exact supplier reference before release. It may be a wording correction or an actual product change. Only the reference mapping can distinguish them. A real substitution reopens the affected installation and surface review.

For a conference room, the selection usually needs to balance a clean wall, repeatable operation, clear sightlines and simple control. For a classroom, consider the screen height, student viewing positions and daily operation through the Education Classroom application page.
For a commercial display environment, a visible casing may be part of the equipment language, but the project still needs service access and a documented control path. For a dedicated home theater, compare a fixed frame before selecting a retractable enclosure.
Request a finish sample or reference when color, gloss or visible seams matter. Check bracket, cable-entry and end-cap details that a product photograph may hide, then record the approved finish and orientation on the drawing.
Service planning is equally important. Identify how the motor, controller, roller and fabric can be inspected without removing unrelated ceiling or wall finishes. For replacement projects, record the existing housing width, image size, drop, material and control method. A visually similar enclosure may still require different brackets or wiring.
An exposed casing can make silhouette and finish important. A casing behind joinery can make complete depth, mounting position and service access more important. Neither priority changes the image requirement, and aluminum alone should not be ranked as lighter, quieter or longer-lived without applicable complete-product data.
| Project priority | Decision after the candidate is identified |
|---|---|
| Exposed housing on a designed elevation | Compare the actual finish and profile after essential fit is accepted |
| Housing within existing joinery | Compare complete section, supports and removable boundaries |
| Detailed image task | Evaluate the actual surface and any side-support arrangement independently of casing appearance |
| Repeated installations | Keep the accepted configuration and any room exceptions explicit |
In a hypothetical refurbishment, the client prefers the Square Aluminum Casing appearance. Its reviewed proposal requires a revised decorative enclosure; another accepted candidate fits the existing joinery. The choice is whether the appearance preference justifies that surrounding work, assuming both image and control arrangements meet the brief. This is a project trade-off, not evidence that one housing family is generally superior.
A useful recommendation therefore reads: “Select this exact configuration because its accepted section fits, its evaluated surface meets the task and its documented operation meets the room sequence.” It names the outcome behind the preferred product rather than ranking a casing adjective.
An assumed enquiry reads: “Meeting Room East: Square Housing Electric Projection Screen; required visible image 2.40 m × 1.35 m, 16:9; exposed installation shown on the room section; separate screen control. Identify the exact proposed model, configuration and included accessories.” The dimensions are hypothetical requirements, not an available-size claim.
Use separate lines if alternatives are wanted.
A casing comparison should be made after the image and material requirements are understood. Matte white, grey, ALR, UST/CLR and acoustic transparent surfaces can behave differently under the same projector and room light. Use the Screen Materials Hub and the ALR versus matte white guide to frame the sample discussion.
If the projector is short-throw or ultra-short-throw, confirm the material and installation angle for the exact product. If speakers sit behind the image, evaluate an acoustic transparent surface as a combined image and audio decision.
Before approval, document:
When the project requires drawings or version control, use the Factory & Production page for manufacturing context and request the current technical package. Send the final requirement through Contact MGF Screens.
MGF can compare suitable product directions once the project brief confirms visible image size, aspect ratio, projector geometry, material direction, mounting condition, control requirements, quantity and destination market. The final quotation should identify the exact model, compatible material, drawing and approval information rather than treating a generic guide as a product specification.

The terms describe different construction or profile attributes and cannot be ranked without the exact model, material and fixing method.
No. Image flatness depends on screen type, fabric, tension system, installation level and operating conditions.
Only if the exact product is designed for it. Confirm rough-in, closure and service access with the model drawing.
The better option is the one that matches the approved drawing, repeatable specifications, packaging and service process. Appearance alone is not enough.
Send MGF those full catalogue references with the limiting room section, required picture dimensions and appearance preference. The resulting side-by-side response can then compare the candidates that were actually intended.